짜잔 의자 설치 성공 그리고 캠핑카 의자의 숨겨진 비밀 Part.22 튜비! 자작 캠핑카 만들기

2 months ago
안녕하세요 캠핑카조아 루시입니다. 저변 편에는 자작 캠핑카 의자 수정작업을 진행했었는데요. 저희가 원하는 캠핑카 의자의 형태와 그리고...

English subtitle

Hello everyone, it's Lucy with Campingcarjoa.
Last time we installed
the hinges for the backrests.
We're going to install the supports
for when we lift up the backrest.
So our plan is...
We should use a compass ruler
But we forgot to bring it.
So
We going to use what we have on hand.
So we made a template.
Take a look.
We drew a line at about 15 degrees.
That's the angle we want our backrest to be.
So we drew a line at a 15 degree angle.
I'll cut this template
and use it to install the backrest supports.
Will it fit?
Will it fit?
To hold up the backrest
We making supports.
The supports will fold out
and anchor here.
That's the plan at least.
But the tricky part is
Getting the supports cut just right.
So we....
We'll use this box to make another template.
I'll cut it out and adjust the fit.
Once it fits, I'll trace it onto the plywood.
I already ate all the icecream :)
The template for the supports is done.
This scrap wood will be the test piece.
I've traced the template onto the test piece already.
After cutting it out, I'll check to make sure it fits.
If everything is okay, I'll trace the actual supports.
I cut the test piece.
But...
Take a look.
It doesn't fit.
It's too long.
So it won't go in.
Even though we copied the template
I guess the template was a little off.
I need to cut about 2 meters.. 2 millimeters.
And test it again.
They're all done.
I used the jig saw and circular saw to cut them.
I tested them and they fit okay.
They fit in just like this.
And they'll support the backrest.
You can see the hinge here.
To find the spot to drill on the supports
we mounted them to the backrest.
We'll attach the supports here.
After the hinge is secured to the supports
we'll set them back on the backrest.
Anyways...
Some of the cuts were a little off.
But we used sandpaper
to adjust the fit..
And we'll do that for the rest of the supports.
Yay!
How does it look?
It works!
Take a look.
This is the backrest supports.
You can see them right?
Just like this, they support the backrest.
And also support on this side.
And now I can sit down!
Oops I cut off my head :)
I'm sitting down everyone!
We still need to make the cushions.
I still have plenty of head room.
And sitting on the seat feels...
Good, very good :)
It wasn't easy getting to this point.
We had problems with the original hinges.
So it took longer than we planned.
But it's nice to finally get it done.
Tomorrow we can sit down
to have lunch while we are working!
Now time to finish up the work.
Incase you didn't know how Tubi is going to look.
We made a 3D drawing of the plans.
If you haven't seen it yet
you can click on the 'I' to watch the video.
But there is a part we didn't show.
If you've gotten this far
maybe you're our loyal fan :)
So I want to give you a sneak peak.
This is really the secret ending.
Right now our seat is set up like this.
You might wonder what the hinges on this side are for.
The reason is...
Clean this up a bit.
This will raise up like this.
But why does this part also go up?
The reason why is
later we'll install supports on this side too.
So this become a backrest.
And if you lower this back down
you have another seating position!
Am I too excited about this?
Anyway, this is just for you guys to know.
Later we'll show everyone how it works.
But we wanted you to know first.
Now back to work.